如何制作一个超声波冷雾加湿器

制作步骤

Step-by-Step Instructions

1. 准备容器盖子
   Prepare the Container Lid

   在塑料容器的盖子中心挖一个适合白色PVC连接件的大孔，并在周围均匀打几个小孔作为进气口。

   Cut a large hole in the center of the plastic lid to fit the white PVC connector and drill several smaller holes around it for air intake.

   
2. 组装PVC部件
   Assemble the PVC Parts

   将红色PVC弯头与白色PVC连接件组合在一起。

   Combine the red PVC elbow and the white PVC connector.

   
3. 固定PVC到盖子
   Attach PVC to the Lid

   使用热熔胶将组装好的PVC部件牢固地固定在盖子中心的大孔上，确保密封。

   Securely glue the assembled PVC part to the large central hole on the lid using hot glue, ensuring a tight seal.

   
4. 安装散热风扇
   Install the Cooling Fan

   将DC散热风扇固定在盖子的底部（内侧），使其叶片正对PVC连接件的开口，用于将雾气吹出。同样使用热熔胶固定。

   Fix the DC cooling fan to the underside (inside) of the lid, positioning its blades directly under the PVC connector opening to blow out mist. Use hot glue to secure it.

   
5. 安装电源插座
   Install the Power Socket

   在盖子上合适的位置打一个小孔，安装DC电源插座。

   Drill a small hole in a suitable location on the lid and install the DC power socket.

   
6. 连接风扇与插座
   Wire the Fan to the Socket

   将散热风扇的电线连接到DC电源插座上。红色线通常接电源插座的中心正极触点，黑色线接外部负极触点。使用电烙铁焊接牢固。

   Connect the fan's wires to the DC power socket. The red wire typically connects to the center positive terminal of the socket, and the black wire to the outer negative terminal. Solder them securely using a soldering iron.

   
7. 准备塑料容器
   Prepare the Plastic Container

   在塑料容器的侧面靠近底部的位置打一个小孔，用于引出雾化模块的电源线。

   Drill a small hole in the side of the plastic container near the bottom to pass the mist maker module's power cable through.

   
8. 放置雾化模块
   Place the Mist Maker Module

   将超声波雾化模块放入容器底部，通过侧面的小孔将电源线引出。确保模块可以完全浸没在水中。

   Place the ultrasonic mist maker module at the bottom of the container, threading its power cable through the small hole on the side. Ensure the module can be fully submerged in water.

   
9. 加入水
   Add Water

   向容器中加入足量的水，至少要没过雾化模块的传感器部分。

   Add sufficient water to the container, at least enough to cover the sensor part of the mist maker module.

   
10. 组装并测试
    Assemble and Test

    将带有风扇和PVC部件的盖子盖到容器上，并连接外部12V电源。超声波雾化模块会产生雾气，风扇会将其从红色弯头处吹出。

    Place the lid with the fan and PVC parts onto the container. Connect an external 12V power supply. The ultrasonic mist maker module will produce mist, and the fan will blow it out through the red elbow.